We have included directions which explain the mixing and coverage of the table top epoxy. Although most epoxies will yellow over time, some resist yellowing caused by exposure to ultraviolet light better than others. Our epoxy contains UV Inhibitors which help to resist yellowing. 1 : 1 By Volume Mixture. 50% Base Resin 50% Curing Agent by VOLUME.
Perfect For A Variety Of Projects. Some of the most common uses for our epoxy are outlined below.
Customers are continually exploring new applications for epoxy. When in doubt, ask questions to assess the suitability of product for particular projects. Bar Tops & Table Tops.Easy To Use 1:1 By Volume Mixture. Self Leveling, Impact Resistant, Superior Air Release. Popular uses include wooden bar tops, river tables, embedding pictures or embedding solid objects into a desired surface. Because our epoxy cures crystal clear, multiple layers will not compromise color/transparency.
Each poured layer should not exceed 1/4 at a time. How Much Epoxy Do I Need?
Our rule of thumb regarding coverage is 12 sqft per mixed gallon at 1/8 inch. Family Owned Business, Made In USA. One mixed gallon covers approximately 12 sq. Coverage must include surfaces, edges, and an extra 2% for run off on the edges.
Although it is not possible to address every type of surface the following is a generic guideline: Bare wood should be sealed with a thin coat of epoxy, decoupage articles should be tested for color fastness prior to application. When re-coating an existing coating the coating should be scuff sanded and cleaned with a cleaning solvent. Denatured Alcohol or Isopropanol 99% are recommended. Be sure that the surface and the epoxy to be mixed are at the same temperature.
Mixing is the most important part of the project. Improper mixing will cause soft or tacky spots in the surface. First be sure you are preparing to mix containers of Hardener and Resin, believe it or not mistakes happen, check the labels. Graduated mixing containers are recommended for measuring and mixing.Hand mixing with a paint type stir stick is recommended, mixes should not exceed 1.5 gal. Continual mixing including sweeping the sides and bottom of the mixing container while mixing should take approx. The product may cloud a little during mixing but will clear as mixing nears completion. It is important to mix without inducing air. After mixing is complete, allow the mix to stand 3-5 minutes and remix for approx.
The completed mix should then be poured into a separate container for the final pour. The reason for this is that no matter how complete the mix is, there are unmixed portions on the sides and bottom of the mixing container. Epoxy is self leveling, therefore the surface must be level for uniformity. The epoxy may be poured on the surface and spread with a plastic hand squeegee or a dust free foam brush. It is not recommended to apply more than 1/8 in.
Thick films are achieved through multiple coats. Once the epoxy is applied to the desired thickness tiny air bubbles will appear on the surface. The bubbles need to be eliminated by passing the flame of a propane torch systematically over the surface keeping the flame at least 3 inches from the surface. The same technique can be used with a heat gun. It will be necessary to repeat this process until the bubbles stop surfacing.
You will now have a glass like surface. Cure times will vary with temperature and thickness.
Fiberglass Supply Depot Table Top Epoxy will be tack free in a 1/8 in film at 77deg, F in approximately 8 hrs. And ready for service in 24 hrs. Important note: Even though the film will appear hard the epoxy will not reach full cure for 14 days.
Therefore, do not leave objects on the surface until fully cured. When used for bars or table tops any hot items like coffee cups hot plates etc. F will leave a ring or impression on most any epoxy.The use of saucers under cups and heat resistant pads under hot plates are recommended to preserve the finish. Epoxies cure through chemical reaction. The chemical reaction generates heat, the greater the mass of epoxy the faster the reaction occurs. Pot life is measured with about 4-0z. Therefore a stated 40 minute pot life is for those 4 ounces. 1.5gal mixes in a bucket will only have a 10-15 min pot life. Epoxies will amber slightly when exposed to sunlight, even for only several hours and will chalk in exterior applications. For exterior application a topcoat with a UV inhibited Urethane is recommended. Blemishes caused by contaminants or suicidal insects can be sanded out and re-coated without ruining clarity. If this is your first experience with Epoxy. EXPERIMENT ON A SIMILAR SURFACE before making a big mistake. Although our epoxy is UV resistant, which resists yellowing, we do not recommend leaving finished projects in direct sunlight or for permanent outdoor applications. Kit contains a half gallon of resin and a half gallon of hardener. We are a family owned and operated business located in Fort Pierce, Florida. Our knowledge comes from years of hands-on experience in the fiberglass repair and manufacturing businesses.
Let us put those years of hard work to your advantage! Customer service and making sure you get the right products for the job is our number one goal. We are a family business with very high standards. Shop here at Fiberglass Supply Depot and we promise you won't be disappointed.We stock: Fiberglass cloth, Fiberglass Mat, Fiberglass Biaxle, Polyester Resin, Epoxy Resin, Glues, Putties, Marine Paints, Sandpaper, detailing and buffing supplies - everything to get the job done, right! UPS next day, two-day or three day select can be accommodated for most orders upon request and will be invoiced accordingly. Most orders placed before 2:00p. This item is in the category "Crafts\Multi-Purpose Craft Supplies\Crafting Pieces\Resin Craft Molds & Supplies". The seller is "fiberglasssupplydepot" and is located in this country: US. This item can be shipped to United States.